Panel Builder System Integrator

July 6, 2020

Discrimination studies are an essential factor in the design of any electrical installations. Professionals carry out an exhaustive analysis of the electrical protections needed to guarantee the continuity of supply in case of failure. A good discrimination study allows the coordination of different protections at different levels of electrical installations.

In fact, the proper setting of the protective devices allows us to easily identify where the fault has occurred. More specifically, the selective coordination generally describes the selection of the protective devices to isolate the overcurrent condition so that the device nearest to a fault will trip rather than any device further ahead of it.

What is a selectivity study?

The terms “discrimination” and “selectivity” refer to the electrical current tripping of a device or piece of equipment and describe the same concept. This is due to the system being coordinated to discriminate between incoming and outgoing devices and prevent any further outgoing fault current from affecting the entire system.

Electrical engineers often produce a discrimination (selectivity) study at various stages within a project. The main point of the discrimination study is to demonstrate that:

  • Electrical equipment is protected by the system protection equipment (circuit breakers etc).
  • The protective devices have compatible characteristics to ensure that protective equipment closest to a fault, operates first.
  • Electrical equipment not involved with the fault remains in service to guarantee the power supply

An electrical network could be exposed to different types of overcurrents such as short-circuits, overloads, voltage dips, or earth faults. There exist different types of discrimination techniques that depend on the type of fault and prevent the electrical network from being affected. However, the goal is to isolate the faulty condition by operating only the nearest upstream overcurrent protective device.

Total and partial selectivity

There are two degrees of selectivity and the correspondent definitions are given in the Standard IEC 60947-2.

Total selectivity

Selectivity is total when for all fault values from overload to bolted short-circuits, distribution is totally selective if only the circuit breaker immediately upstream located above the fault opens.

“Overcurrent selectivity where in the presence of two protection devices against overcurrent in series, the load side protection device carries out the protection without making the other device trip.”

Partial selectivity

Selectivity is partial if the above condition is not fulfilled up to the bolted short-circuit current but only up to a lower value. This value is referred to as the selectivity limit.

“Overcurrent selectivity where, in the presence of two protection devices against overcurrent in series, the load side protection device carries out the protection up to a given level of overcurrent, without making the other device trip.”

elec calc: power continuity and selective coordination

Carrying out a discrimination study is critical to ensure the correct functioning of the electrical system in the event of possible faults. In fact, in the electrical power system designs, power continuity and selective coordination are the requirements to meet.

elec calc is a robust software that offers critical calculations for factors such as earthing systems, cable ampacity, short circuit currents, thermal stresses, voltage drops, and discrimination studies between protections that are key for the continuation of supply.

With elec calc you can check several operational scenarios such as emergency, network change-over – to analyze each operational condition using the behavior and sizing of the installation.

To guarantee project design calculation, quality, safety, and power supply, companies must comply with strict design rules. With elec calc it is possible to proactively save money and reduce costly errors in the design process with quick selection of manufacturer´ or users´ references and verification of installation sizing with the relevant standards.

elec calc complies with IEC standards (as well as many others) – electrical standards compliance – size according to the international and local standards, ensure the correct behavior of the installation and comply with regulations in force.

Domestic-type circuit-breakers must comply with IEC standard 60898, or an equivalent national standard.

EC 60898-1

Defines the behavior of a circuit breaker in relation to AC. low-voltage circuit breakers – Miniature Circuit Breakers (MCBs) – we find in our homes, schools, shops, and offices electrical distribution switchboards.

The standard states that the top-rated current is 125A, while the lowest is 6A and the maximum value of rated short-circuit capacity (Icn) is 25kA. These basic tech specifications tell us how different the use of circuit breakers defined by our two standards are.

Industrial circuit-breakers must comply with IEC 60947-1 and 60947-2 or other equivalent standards.

IEC 60947-2

They protect electrical power distribution of up to 1000 volts AC and 1500 volts DC with the whole spectrum of rated current from 0,5 to 6300A. Utilities and manufacturing facilities use them: air circuit breakers (ACBs), Molded Case Circuit Breakers (MCCBs), and miniature circuit breakers (MCBs).

Safety can be combined with the continuity of service using elec calc and the fault easily located. It is an especially important point for high-powered equipment since this is generally located at the head of the installation and therefore has even greater consequences in the event of false tripping.

Real-time – elec calc with its unique features such as HV/LV real-time calculations, its intuitive and intelligent design mode, Intellisense, and its multi-level discrimination functionality, helps ensure the maintaining of power supplies. That is why elec calc features a discrimination study by a free selection of components along with a dynamic graphical setting of the device with an adjustable zoom.

All these factors are vital within the sector for energy production, energy transformation, or energy distribution.

That is why the correct type of discrimination study is essential. For each type of fault, there is a specific protective device (protection against overload, short-circuit or earth fault currents, or against loss of voltage, etc). Each of these faults can cause a loss of discrimination if the coordination of the protective devices has not been considered. elec calc software features all the necessary functions and features to carry out a complete analysis of installations with detailed studies, giving you the very best solution for your project.

Source

Changing Scene

  • Prev
Attend this webinar to solve your automation challenges and become more productive.   ...
Safety, efficiency, and smart design are essential when designing panels and systems.   ...
Eclipse Automation had the pleasure to host Premiere Doug Ford, Minister Victor Fedeli, and caucus ...
The HARTING Technology Group continues to briskly advance the pace of digital transformation. “The ...
Spartan Controls and AltaML are pleased to announce they have entered into a formal partnership and ...
Omron Automation, a leading provider of industrial automation solutions, congratulates Taylor Fluid ...
On July 15, EPLAN Canada will host an Added Value Webinar focused on routing, wiring and production ...
Eramosa, a North American provider of SCADA, network, cybersecurity, operational technology, and ...

RS Components Launches New Season of the DesignSpark Podcast Tackling Technology With a Comedy Twist

RS Components DesignSpark PodcastRS Components (RS), a global multi-channel provider of industrial and electronic products and solutions, has released a new series of its popular ‘DesignSpark Podcast’ which explores some of the hottest topics in technology through a mix of fun facts, exuberant stand-up, outlandish sketches and foot-tapping songs. The podcast offers educational information on each technology topic, with an entertaining comedy angle.

The new weekly podcast is co-hosted by technology expert Professor Lucy Rogers PhD – former judge on BBC’s Robot Wars and a DesignSpark blogger – alongside award-winning comedians Bec Hill and Harriet Braine.

Read More

 

Module_Divider.png

JMP Solutions and Control Station Announce Exclusive Collaboration Focused on Optimizing Manufacturing Output and Efficiency

JMP SolutionsJMP Solutions and Control Station are joining forces to provide process and control loop audit services for manufacturing environments in order to identify and optimize problematic and underperforming control loops. The partnership leverages the complementary skillsets of JMP’s expert process engineering and project management competency combined with Control Station’s proprietary process analytics platform which, will work in synergy to identify and correct PID loop related sources of inefficiency and sub-optimal performance.

Read More

 

Module_Divider.png


Proax Is Now a Distributor of HIWIN

PB-34-Proax-HIWINLogo-400.jpgProax are pleased to announce that they are now a distributor of the HIWIN product line, a leader in motion control and system technology. Their product offer includes linear guideways, ballscrews, actuators, linear motors, torque motors & rotary tables, crossed roller bearings and more. This addition comes in line with the enhanced mechanical team and product offering announced last year by Proax. This newly added line will be available to all Proax's clients throughout Canada since this is going to be implemented on a national level.

Read More

Cybersecurity and Manufacturing – Keeping Critical Information Safe From Attackers

JAE AutomationWe all know that we’re supposed to back up our data and secure our devices against attack. But too often we put it off until it’s too late. We’re busy, and we’ll get to it another day. And then, one day, we turn on our device, look for a file, and realize something is wrong. We’ve been hacked.

The thought of losing our files, pictures, and data is scary. Scale that up to an entire company and the consequences can be severe. Think about the amount of critical and sensitive information the typical manufacturing facility has access to. Sensitive customer records, design and engineering data, intellectual property, and industrial control systems for high risk manufacturing processes – there’s a lot to lose. 

Read More

 

Module_Divider.png

Phoenix Contact Control Cabinet Classroom Ep. 6: How to Determine Supplementary vs. Branch Circuit Breakers

Phoenix Contact Control CabinetSometimes it can be difficult to distinguish between types of circuit breakers, especially since in appearance they look so similar. In this episode, the focus will be on the differences between two types of circuit breakers: Branch and Supplementary.

In the Control Cabinet Classroom video series, Phoenix Contact Product Specialists Zach and Karen break down some of the basics of control cabinet design, terminology and technology to be able to better understand and utilize this powerful solution.

 

 

Read More

Product News

  • Prev
The NaviTEK IE is a tester for commissioning, preventative maintenance, and ...
R. STAHL is authorized to certify customer-specific systems for installation in hazardous ...
Maplesoft™ announced the release of MapleSim™ Insight, a new software product from Maplesoft that ...
Yokogawa Electric Corporation announces the release of new pressure and temperature sensors for the ...
Branson™ GL-300 platform increases production capability and enables faster production start-up. ...
Omron Automation Americas launches the heavy-duty HD-1500 mobile robot with an exceptionally large ...
The superior safety of Eaton’s Arrow Hart ultra grip locking devices has been enhanced with colour ...
IDEAL Safe-T-Grip® Fuse Pullers are made of molded, tough, high-impact nylon for greater strength ...
As summer heats up Rittal will be announcing two new updated LCP product lines.     ...
As of April 1, Rittal has changed the portfolio of signal pillars to the latest LED technology. ...
Kerrwil Publications Great Place to Work. Certified December 2019 - December 2020

538 Elizabeth Street, Midland,Ontario, Canada L4R2A3 +1 705 527 7666
©2020 All rights reserved

Use of this Site constitutes acceptance of our Privacy Policy (effective 1.1.2016)
The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Kerrwil